new record cutting forum online !

Discussion in 'Mastering' started by AM-32B, Jun 3, 2005.

  1. AM-32B

    AM-32B Guest

    (Edited by the Moderator.)


    Please, No Spamming!
     
  2. drones

    drones Guest

    vinyl cutting forum

    where can this forum be found?
     
  3. AM-32B

    AM-32B Guest

    forum access

    hi, look at my homepage :wink:
     
  4. Michael Fossenkemper

    Michael Fossenkemper Distinguished past mastering moderator Well-Known Member

    AM-32B,

    If you want to participate in this forum and add something, great. You are more than welcome. But if you are just looking to pimp yourself here, then you are not welcome. This is your 3rd post, the 4th is your last chance.
     
  5. Ammitsboel

    Ammitsboel Member

    Re: forum access

    Is that your portable stereo you got there!?
    I take it as you like Neumann very much.
     
  6. AM-32B

    AM-32B Guest

    portable...

    yes, it´s originally the head from the kingston dubplate cutter 1210 overhead.... the electronics is modified and a stronger poweramp is added to cut louder. I am very happy with this configuration... :D
     
  7. Ammitsboel

    Ammitsboel Member

    What poweramp are you using then?
     
  8. AM-32B

    AM-32B Guest

    harman+kardon citiation 22
     
  9. Ammitsboel

    Ammitsboel Member

    Are they 100W pr channel?
     
  10. AM-32B

    AM-32B Guest

    a bit more 8)
    but thats enough...for sx74 it´s good to have 400watts and more, but my sc-99 has stronger magnets (rare earth i think...)

    Citiation 22:
    Power Output : 200 watts per channel @ 8 ohms
    Total Harmonic Distortion : 0.08% @ 8 ohms
    0.08% @ 4 ohms
    Output 4 Ohms : 200 watts per channel
    High Instantaneous Current Capability (HCC) : +/-120 amps
    Negative Feedback : 12dB
    Frequency Response : 0.1Hz - 250kHz +0/-3dB
    Slew Rate : 160 volts/microsecond
     
  11. Michael Fossenkemper

    Michael Fossenkemper Distinguished past mastering moderator Well-Known Member

    thank you AM-32B.

    There are some vinyl guys around here. I would like to see more discussion on cutting so please stick around and hash it out.
     
  12. somastring

    somastring Guest

    yes yes postpost post reactions vinyl cutters.....
     
  13. HansAm

    HansAm Active Member

    So? What would it cost me to get a test cut? I have something that i would like to have on vinyl, but the number isnt all that greate so im thinking cutting them might be cheaper than pressing.
     
  14. jason

    jason Guest

    Hans Am,
    Where are you based if you are in the UK i can do a test cut
     
  15. AM-32B

    AM-32B Guest

    Dubplate Cuts 12inch@45RPM are arround 60Euros (max. 9min per side)
    10inch@45RPM is a bit cheaper (max.7min)
    contact me, if you want more details...
    :)
     
  16. jason

    jason Guest

    Am-32B
    Did you get that lathe from Flow?,What signal path have you got betwwen the source and the amps?
    Jason
     
  17. HansAm

    HansAm Active Member

    Im located up in Norway :D Ill post again when my band is done in the studio.
     
  18. AM-32B

    AM-32B Guest

    @jason:
    the lathe is from vinylium, switzerland, I can reach them in 4 ours with a small truck :D
    the am-32 was originally based in france at the manley studios...
    I installed vinyliulm pitch controller, and updated my cutting electronics....
    it was much work, because the lathe was in near original condition, with tube pitch, old motors, sitches and and and....
    my preamp/riaa is a modified beta kinston electronic, but with best op-amps, caps+coils...
    here is a little story (german), but many pics:
    SPL 2384
     

Share This Page