1. Register NOW and become part of this fantastic knowledge base forum! This message will go away once you have registered.

recording a violin

Discussion in 'Accessories / Connections' started by naftali94, Jun 26, 2009.

  1. naftali94

    naftali94 Active Member

    sorry about my english. i'm not know english good.
    i play on violin and i want to record me in my comuter..
    i use AUDACITY.
    i have a good pick up in my violin (somthing of barcus-berry).
    andd i connect a PL cable to my comuter. but the problem is that the sound isn't good!!!. it's sound metallic.
    i will be happy if somone can guide me what i can do. thank you.
     
  2. Cucco

    Cucco Distinguished Member

    Hi naftali94 -
    No need to apologize for your English. Your question is perfectly understandable.

    I've never found a pick up that represents a bowed stringed instrument well. Granted, the Barcus Berry stuff is pretty decent, I think you'll always get a metalilic sound using a pickup.

    However, I'm assuming you're taking your output from your pickup straight into the line input on your computer??

    You'll want to take that pickup into a direct box - one that converts the resistance and levels to match with the line input on your computer. Cheap direct boxes can be had for around $29 or so (USDollars). These are typically passive devices and work quite well.

    My favorite all-around DI (direct box) is the Radial J48. It works for every source I've ever used it on. Sure, some DIs sound better on some sources, but the Radial sounds good with everything and great on a lot of things. For violin with pickup, there's only a handful of DIs that I would rank higher.

    Cheers and best of luck!
    Jeremy
     
  3. naftali94

    naftali94 Active Member

    thank you!

    thank you about the answer.
    you righted. i conected the cable only to the computer.
    i didn't understand yet what is exactly "direct box". if you can explain me again.
    i see that there are "passive" and "active". what the difrence and what i need?.
    can't i do anything to improve the sound on the computer-with the software (audacity)?
    naftali.
     
  4. Guitarfreak

    Guitarfreak Well-Known Member

    A direct box changes the signal's impedance from high to low or low to high if you run the signal backwards. 'Passive' means it does not need power, and 'active' means it needs to be powered in some way. Active direct boxes have preamps in them and good ones cost a lot of money, so you might be better off with a passive box. Then you can reamp too if needed.

    You could definitely edit the soundwaves in Audacity, but in my experience it is best to get the best sound going in so you don't have to. Starting with bad sound means you'll have to do major editing via EQ or other plugs and the end result will sound very 'processed' and unnatural. Just try to get the best capture that you can. I would also recommend using mics instead of the pickup.
     
  5. jg49

    jg49 Well-Known Member

    Just to clear this up a little, active DI boxes are not necessarily preamps. Take this one for example
    http://www.radialeng.com/di-j48.htm
    or this one
    http://www.countryman.com/store/product.asp?id=52&catid=3
    which are for the most part industry standards. You will notice that there is no gain control on either one. They are not considered preamps.
    There are some on the market like this LR Baggs Para DI
    http://www.lrbaggs.com/html/products/preamps_paradi.shtml
    which is a preamp and has gain and tone settings usually used from an acoustic instrument, guitar, mandolin, etc. that has some type of pickup installed but does not have a volume or EQ set up. An example is Gibson's Hummingbird with pick up. This unit gives the musician some control over their instruments gain and tone on stage when going thru FOH, though I am sure there are other uses
     

Share This Page