1. Register NOW and become part of this fantastic knowledge base forum! This message will go away once you have registered.

to " VU " or not to " VU"

Discussion in 'Pro Audio Equipment' started by Sanity Inn, Jun 21, 2003.

  1. Sanity Inn

    Sanity Inn Guest

    Hi, i'm trying to understand how important a VU meter on a mic pre is, to some of us,,


    Myself , I beeing novice and all, will probably depend on it until I know what things need to use "pad " or not, etc,,,
    that's why I ordered mine with VU's

    Seeing there are many products out there that are VU less, is this a big issue?? do we preffer it on or off the unit?


    Also, the " phase switch" is this a switch one uses often?


    Thanks for your help, I appreciate any and all views


    Sanity Inn

    " Logic rules, emotion wins "
     
  2. anonymous

    anonymous Guests

    not having a VU is really no big deal...considering the fact that if you are using a preamp your more than likely recording to some form of MTR which will probably have some type of track metering.
     
  3. Sanity Inn

    Sanity Inn Guest

    thanks scenaria,

    OK , let's use this example,
    say I have a VU less mic pre, I have my guitar plugged into the DI at 0db pad, ( should be -15db) to me it's sounding nice, I route this to my VS-880 and I set levels there....

    I can understand your point on levels at the next source, but what if was recording distorted signal unknowingly,,, or would it be obvious?

    thanks again

    Sanity
     
  4. anonymous

    anonymous Guests

    im not familiar with the VS-880 but im gathering its a mixer/recording kinda box? which has some faders for setting levels? I would set my fader at unity (zero) and set my ideal record level with the preamp.
     
  5. realdynamix

    realdynamix Well-Known Member

    :) Hi! I'ma gonna jump in here head first. One question though, does the unit have an output level control?

    Let's say the output is fixed at +4db. If you jack in your guitar, and bring up the level, and watch your downstream metering, you should be able to tell if you need to use the pad by the amount of gain you are using. If it overdrives at a setting outside of normal (too sensitive), then you click in some pad. Things change a little if it has an output control, because you may want to overdrive somewhat for some effect (saturation).

    Any help? I just topped a tree, and this distraction really helps with the pain, LOL.

    --Rick
     
  6. Sanity Inn

    Sanity Inn Guest

    Rick Ty ,

    I'm slowly saturating this stuff, lol,,

    OK to make it simple I went with the Sebatron vmp20002 VU, VRS non VU, as the novice , i wanted some point of refference.
    I'm trying to understand the over all " real need " of the unit having one and buying the extra cost of it rather then saving money on the VU less version.

    I figure this unit has 1 gain control called output level, but I think I know what you mean with the Gain knob and then an output knob, which I understand both have pros and cons,,


    I'm trying decipher whether I actually needed the VU's and will consider this in future units I plan on

    did you care to touch on whether a unit really needs a phase switch?

    I appreciate your time

    Sanity Inn

    " Logic rules, emotion wins"
     
  7. Sanity Inn

    Sanity Inn Guest

    oops

    let call it

    sebatron vmp2000e VU

    sorry for typo
    :)
     
  8. realdynamix

    realdynamix Well-Known Member

    :) Ahhh more pain relief. The switch, it is a convenience. If you had to do a phase reversal, you can use a modified well marked cable. But, if you are going to use a bunch of them, the switch(s) would be preferred.

    I think the VU necessity is for systems where inputs need to be monitored at the source, where outputs go to unity gain fixed type installations. Like a radio station, TV v/o room, or small installation where operators need input control, with everything else located elsewhere. They are pretty though.

    --Rick
     
  9. Sanity Inn

    Sanity Inn Guest

    Thanks again Rick


    "" They are pretty though.""

    lol thanks for the chuckle


    Sanity Inn
     
  10. Sanity Inn

    Sanity Inn Guest

    oops

    and thanks scenaria imissed your 2nd post

    :)

    Sanity Inn
     
  11. byacey

    byacey Active Member

    When I built my preamp I added a metering circuit as well as clip LEDs. After using it for awhile I found the meters do not offer much in the way of useful information unless you are blindly sending a signal from a remote location and you want to ensure that there is signal at some sort of reference level. The LED clip indicators on the other hand are far more useful.
    Bill Y.
     
  12. Richard Monroe

    Richard Monroe Active Member

    I find vu meters very useful, but that is because I am hearing impaired, and I have to track largely by the numbers, which is why I'll never be a pro engineer. Sometomes it can take me a month of trial and error to get mic placement right on a given source. When you're going from an outboard pre into a standalone (a recorder mixer thingy??!), you're mission is often to send the standalone the hottest possible signal to bypass the cruddy pres in the standalone as much as possible. This means you will come pretty damn close to clipping the outboard pre. In the end, I don't think it matters whether you have vu meters or LED meters, or just a clip indicator. What matters is how truthful those indicators are, and how much headroom you have beyond the indicated clip level. God, I envy you guys with good ears!-Richie
     
  13. Sanity Inn

    Sanity Inn Guest

    Just want to say thanks for the input on this,

    Peace.


    Sanity Inn
     
  14. vinniesrs

    vinniesrs Active Member

    Sanity, I don't think you need the vu meters, but the phase switch is somethin I wouldn't turn down. If you are really serious about making quality recordings, you need to be on top of the phase issues from point 1. Yes, it can be done with a cable, but a switch is way faster and allows for quick finding phase problems while setting up.
     
  15. sdevino

    sdevino Active Member

    If your studio is well calibrated then you do not need the VU meters on the pre (except as noted above). A well calibrated DAW will use a calibrated line level test signal usually +4dBu to set the DAW meters to between -16 and -20 dBFS, lets say -18dBFS for now.

    That means if you track at about -18 dBFS on yor DAW meters your mic pre will be running around 0VU.

    0 VU will give you max head room with resonable signal/noise. -18dBFS will give you excellent head room on the DAW and probably close to 90dB s/n. Basically the DAW wil be very happy so now you can track a little lower for more headroom and extra clean sound or a little more aggressively depending on sound.

    The Sebatron allows you to run the pre hot (slightly overdriven) or very clean. Depending on how you set the pad vs output level.

    If you run your levels this way it takes about 5 seconds to set level and you can place mics and set drive levels for taste and sound quality without worrying about the converters.

    Its funny but you actually get more performance from your converters by leaving some headroom than by tracking hot.

    Steve
     

Share This Page