1. Register NOW and become part of this fantastic knowledge base forum! This message will go away once you have registered.

Yamaha 01v and Cubase SX

Discussion in 'Cubase' started by roby26, Aug 22, 2004.

  1. roby26

    roby26 Guest

    Hello all,
    :-?

    Just purchased on 01v online and was looking for a information on how to setup within Cubase for audio\vst recording playback. I have a RME 96/52 card in my machine with the IN\OUTS going correctly from the O1V into the 96/52.

    If a record a vocal or a VST piece(the Grand or something like that),I can see the mixer generating movement and it does record something, just no sound on playback.
    I can also move the sliders in cubase using the O1V, so that's not a problem. Just can't hear anything.
     
  2. roby26

    roby26 Guest

    :)...and yes, I have monitors plugged into the O1V...both in the stereo and monitor outs(2 sets of monitors.)
     
  3. boheme6

    boheme6 Guest

    by 'directly to the 01v' - does this mean that you're using the option card in the 01v? Is it the lightpipe card?

    If so - you have to turn on the option i/o channels to hear it back (and route stuff to the i/o channels to record them).

    The 01v manual (downloadable from Yamaha) has a pretty good explanation of this.

    Also, the Yahoo 01v group is helpful.
    "-)
     
  4. phulden

    phulden Guest

    I also have a 01V and wonder if anybody knows about the quality of the preamps?
     
  5. Blueberry

    Blueberry Active Member

    A Focusrite Platinum series mic pre is cleaner and more open.
     
  6. roby26

    roby26 Guest

    Yes, I have an Option card going into my 96/52 card. You know, I went through the manual this weekend, and I'm not picking up how to do it. Could you walk me through the part where you say...

    "you have to turn on the option i/o channels to hear it back (and route stuff to the i/o channels to record them). "

    That would be great!..

    Thank you in advance. :oops:


    --------------------------------------------------------------------------------
    by 'directly to the 01v' - does this mean that you're using the option card in the 01v? Is it the lightpipe card?

    If so - you have to turn on the option i/o channels to hear it back (and route stuff to the i/o channels to record them).

    The 01v manual (downloadable from Yamaha) has a pretty good explanation of this.

    Also, the Yahoo 01v group is helpful.
     
  7. damienthorn

    damienthorn Guest

    It sounds like you need to look at your total mix settings (assuming it's an HDSP9652)
     
  8. roby26

    roby26 Guest

    it's a nuendo 96/52
     
  9. boheme6

    boheme6 Guest

    on the 01v - hit the 'option i/o' button.. and channels 1-8 are now seeing 17-24 (the 8 option card inputs) .. bring up those faders, turn on those channels... and you SHOULD hear playback...

    this is assuming that the software mixer is sending audio out properly.

    As for routing OUT of those - you need to go into the PAN/ROUTING section of the 01v.. from there, you can choose D, which will send a channel directly to it's option counterpart (1/8 to 17, 1/9 to 18, etc) or send channels to bus 1-4, and then send those to the option outputs.
    "-)
     
  10. roby26

    roby26 Guest

    Thanks so much!!!!....got it going.
     
  11. boheme6

    boheme6 Guest

    Now I'll give you the bad news.
    From SX1 to SX2, Steinberg seems to have broken the 01v control template. If you want to control the mixer in Cubase with your 01v now - you can control level.. but that's it. in SX1 - everything worked (level, pan, mute, eq, sends, etc).

    hope they fix it sometime soon.
    "-)
     

Share This Page