Skip to main content

In my opinion (i think most will agree) that after the original source (instrument, amp, etc..) the room that the instrument is being tracked in is the first stage of EQ.

Given that idea I believe you want a general multi-purpose tracking room to have a tight bottom end and bright highs. I'm aware that this is subjective and a matter of taste, application and of course room dimensions.

Example:
1. If you have too much high frequency absorption, the instruments you track in that room will most likely sound lifeless in the high's, due to the lack of good high frequency reflections.
2. If you don't have enough low end absorption, the room will probably be "boomy" and "boxy".

I think it's really easy to overdo high frequency absorption, which leads me to trying to come up with different ways to make thick absorption panels reflective/scattering in the highs yet still absorbing the lower frequency.
I've noticed allot of thick absorption panels in higher end studio's have very thin 1/16 inch wood panels with holes drilled in them.

My question is..
What are different simple ways of going about making absorption panels/walls/ ceilings that scatter highs and absorb the lower frequency's?

Comments

pcrecord Tue, 05/12/2015 - 05:30

ChrisH, post: 428931, member: 43833 wrote: My question is..
What are different simple ways of going about making absorption panels/walls/ ceilings that scatter highs and absorb the lower frequency's?

I'm far from an expert but the first thing to understand is that frequency response of acoustic panels depends on the tickness and type of material.
Before you start anything, you need to know what are the room's defects if any. the best way to do so is actually record in it and analyse the results.
If recordings of vocal, acoustics and other instruments with different mics and placement all give too much 200hz.. that should be your main focus.
Once the 200hz is taking care of, record again.. and so on.. long but you'll get the sound you want.

Going on with calculations and theory is good.. but some go at it with closed eyes and creates problems instead of fixing some.. take your time !

audiokid Tue, 05/12/2015 - 15:08

Kurt Foster, post: 428949, member: 7836 wrote:

[="http://en.wikipedia.org/wiki/Room_modes"]http://en.wikipedia.org/wiki/Room_modes[/]="http://en.wikipedia…"]http://en.wikipedia…]

[[url=http://="http://en.wikipedia…"]Bass trap - Wikipedia, the free encyclopedia[/]="http://en.wikipedia…"]Bass trap - Wikipedia, the free encyclopedia[/]

it blows my mind that for over a decade this site has had some of the industries leading acousticians and not one of them posted information that we can refer people to here. rotf

ChrisH Tue, 05/12/2015 - 15:48

audiokid, post: 428960, member: 1 wrote: it blows my mind that for over a decade this site has had some of the industries leading acousticians and not one of them posted information that we can refer people to here. rotf

I getcha, was just thinkin in the means of different materials for basic scattering of highs? I have not seen that on here, maybe I'm blind?

DonnyThompson Wed, 05/13/2015 - 01:19

pcrecord, post: 428947, member: 46460 wrote: frequency response of acoustic panels depends on the thickness and type of material.

By "type of material" I believe that PC is referring to density, which is important. For example, 3" of Roxul has much more absorbent quality, and can also absorb a wider frequency range, than the same 3 inches of regular household insulation, or even typical auralex can.

Roxul Safe and Sound, Owens Corning 703, 705, etc. are but a few of the common materials used in DIY acoustic treatment. They are light, and can be framed for attachment to boundaries, and can also be easily covered with fabric for nicer looking aesthetics.

And, don't discount using an air gap in-between the back of the material and the boundary you are adhering it to. This can increase the absorption efficiency of the material.

But, you have to know what issues you are treating for first.

FWIW

kmetal Wed, 05/13/2015 - 01:20

ChrisH, post: 428931, member: 43833 wrote: In my opinion (i think most will agree) that after the original source (instrument, amp, ect..) the room that the instrument is being tracked in is the first stage of EQ.

Given that idea I believe you want a general multi-purpose tracking room to have a tight bottom end and bright highs. I'm aware that this is subjective and a matter of taste, application and of course room dimensions.

Example:
1. If you have too much high frequency absorption, the instruments you track in that room will most likely sound lifeless in the high's, due to the lack of good high frequency reflections.
2. If you don't have enough low end absorption, the room will probably be "boomy" and "boxy".

I think it's really easy to overdo high frequency absorption, which leads me to trying to come up with different ways to make thick absorption panels reflective/scattering in the highs yet still absorbing the lower frequency.
I've noticed allot of thick absorption panels in higher end studio's have very thin 1/16 inch wood panels with holes drilled in them.

My question is..
What are different simple ways of going about making absorption panels/walls/ ceilings that scatter highs and absorb the lower frequency's?

Those panels are 'helmholtz resonators'. Tuned broadband bass traps. Just like slats, the pegboard is the same concept. The relationships between board surface, and absorbabtive (holes with insulation behind), along with the depth of the air gap behind it, determine what frequencies it attacks. The more board surface (smaller holes /spaces) absorbs more bass and reflects more highs. So if your room is boomy in the mudrange, build a mid bass trap that attacks that area.

I've been fascinated with polys and curved surfaces, so I'd put them in if I was making a place right now. If I was gonna go with a nice RPG or DIY diffusive/reflective type thing this is the room to put it in. Maybe a nice stone facade on one wall for giggles.

Tracking rooms are a comletely different animal, and I don't belive there is a solid science on diffusion in general, and certainly not in 'how to make an amazing room'. Calculators are unsure for large racking areas where RT60 is a concern, and you need a smooth decay/intelligibility. Also an area where true diffusion has an effect. audiokid There is no easy way to quantify 'good' like there is 'flat', and there's no easy way to calculate flat. So really I think it's a question of having the ability to use high level acoustic modeling, if your gonna pre design a signature into a room, and even then, acousticians know it's an art science, not an exact one. So I think we don't see easy answers to these diffusion, tracking room questions cuz they're t aren't any, and each one is custom. I think doing that would be like us remixing each persons song ourselves, in the mix critique section. I think it comes down to a combination of money, and lack of an solid 1+1 answer

Unless your building it for a specific purpose, like vocals, where there is an expected frequency range you need to complement, then you just need some broadband treatments. A few corner traps, some ceiling absorption, and some wall panels. I usually don't like to have 2 untreated surfaces facing each other, in the couple tracking rooms I set up.

Just tame the room down with well distributed broadband stuff, and you'll probably be fine. You can certlny get into movable panels, or 'live sections' of walls, and have curtains, so you can mess with the liveness. A room this size is probably going to be pretty tight and punchy. Get rid of any obtrusive booms, and slap echoes, and that's about it. Get you natural verb from an adjacent hall, and the 70s guys will smile. There ya go, anything else you need there's a pluggin for.

Your probably gonna want to focus your wall absorbsion so it's at mic level or lower. You can raise the overheads a bit to catch some more life.

If there ever was a good place for 2" foam it's on low ceilings in booths. Saves space and kills the crap your mics never want to hear.

ChrisH Wed, 05/13/2015 - 09:16

kmetal, post: 428973, member: 37533 wrote: The more board surface (smaller holes /spaces) absorbs more bass and reflects more highs. So if your room is boomy in the mudrange, build a mid bass trap that attacks that area.

I've been fascinated with polys and curved surfaces, so I'd put them in if I was making a place right now. If I was gonna go with a nice RPG or DIY diffusive/reflective type thing this is the room to put it in. Maybe a nice stone facade on one wall for giggles.

Thank you, Kyle. Fantastic information and insight as always.

Your statement I quoted above is pretty on track to what my OP was asking about.
I want to build tuned resonator traps that instead of just having a flat holed front surface, it would have more of like a poly curved surface to do some minimal scattering from parallel surfaces. Does that make sense? Basically a Poly Diffuser that is also a tuned broadband trap or resonator, possible?

KurtFoster Wed, 05/13/2015 - 09:27

ChrisH, post: 428981, member: 43833 wrote:
I want to build tuned resonator traps that instead of just having a flat holed front surface, it would have more of like a poly curved surface to do some minimal scattering from parallel surfaces. Does that make sense? Basically a Poly Diffuser that is also a tuned broadband trap or resonator, possible?

you might be able to do that with a slat wall. frame it out with 2 X4s, fill with rock wool, cover that with tar paper and then put up the slats. that [[url=http://[/URL]="http://www.mh-audio…"]calculator sheet[/]="http://www.mh-audio…"]calculator sheet[/] i posted earlier has the formulas for figuring out the spacing of the slats.

kmetal Wed, 05/13/2015 - 12:58

ChrisH, post: 428981, member: 43833 wrote: Thank you, Kyle. Fantastic information and insight as always.

Your statement I quoted above is pretty on track to what my OP was asking about.
I want to build tuned resonator traps that instead of just having a flat holed front surface, it would have more of like a poly curved surface to do some minimal scattering from parallel surfaces. Does that make sense? Basically a Poly Diffuser that is also a tuned broadband trap or resonator, possible?

So a polyfusinator? Lmao. Yeah man I've been toying with that idea for a while. The curved nature of the cavity makes it different than what a typical calculator figuring. But using the same type of thinking you would for a corner trap (where it's a variable depth cavity) I'm guessing, is probably just fine.

If you do nice wide arcs (or whatever the technical term is) then you could bend the slats lengthwise. I'd prefer this over the oak barrel look, of vertical salts on a poly, but that's astchetics. Your also not limited to pegboards, or slats. I think the main consideration is the board surface to space ratio, not necessarily the shape of the cutout. Ante up studios, in I think OH, closed a few years ago, but it was a $3m project according to some article. Chimaira did a crushing album there. They have some cool architectural details in their rooms, but not necessarily, hard to fabricate, at least from the surface anyway. If you can find some pics of this place maybe it will spark some ideas. Forgot we were talking tracking rooms , you might like some of the things they built into blue jay studio, in Carlisle, MA.

With bass trapping, I've always had a hard time trying to quantify, how much of an effect they will have. The center frequency is fairly straightforward. When it comes down to "how many db" in the traps range, it would knock down, in a given area. But since this is a tracking room, it's not quite so critical, as its job doesn't have a particular sweet spot in mind.

Hopefully we can find out more about this type of thing, because after the basic RFZ, it seems to jump right into PHD territory lol.

Fun topics Chris. It's cool when we're all along for the pre production!!!!

OBrien Sat, 05/16/2015 - 22:01

Kurt Foster, post: 428982, member: 7836 wrote: cover that with tar paper

If the goal is to retain the mids and highs in the environment after the inclusion of absorption is introduced I would suggest a flame retardant breathable cloth rather than something as potentiality flammable as 15 or 30 # felt.

If the goal is to contain the air-borne particles of the fibrous insulation...same thing applies.

Rod Gervais Sun, 05/31/2015 - 04:15

ChrisH, post: 428931, member: 43833 wrote:

Example:
1. If you have too much high frequency absorption, the instruments you track in that room will most likely sound lifeless in the high's, due to the lack of good high frequency reflections.

Actually I would not necessarily agree with this commet..........

While it's true that the lack of low end control can be very problematic - a lack of reflections is not the same thing.

If you were to walk into the center of the main rooms in Studios "A" at Avatar NY or Sonalysts in CT and set up to record an acoustic guitar - what you would find is that you had no reflections whatsoever from anywhere in the room (except for what might occur from the floor) if you were to close mic the instrument - and began to pick up the rooms influence if you were to raise the mic into the room.

A mic up in the coffin would be the extreme when it came to reflections.

The lack of high frequency reflections would leave what I would consider a "clean" guitar sound...... you would be hearing the guitar - and just the guitar.....

It is not as if putting that guitar inside of even a completely dead room would some how change the sound emanating from the body of the guitar itself........ it would simply mean that the room did not influence the overall sound.

There is a difference between adding to the sound emanating from the instument and altering the sound of the instrument itself.

You can always add some ambiance to a recorded sound to emulate a more reflective room........ but without reflections what you have is the pure raw sound of the instrument itself. That doesn't suddenly magically dissapear.

Rod

dvdhawk Sun, 05/31/2015 - 18:40

audiokid, post: 428960, member: 1 wrote: it blows my mind that for over a decade this site has had some of the industries leading acousticians and not one of them posted information that we can refer people to here. rotf

With all due respect, you've just missed them because it didn't interest you. I've seen, and read, countless resources over the years that were posted here by acousticians and builders - because it interests me very much. Thanks to Rod, Andre, Brien, Max, Glenn (Gulfo), Wes, Eric, Etc.

Rod Gervais Mon, 06/01/2015 - 03:40

dvdhawk, post: 429482, member: 36047 wrote: With all due respect, you've just missed them because it didn't interest you. I've seen, and read, countless resources over the years that were posted here by acousticians and builders - because it interests me very much. Thanks to Rod, Andre, Brien, Max, Glenn (Gulfo), Wes, Eric, Etc.

I believe you missed the sarcasm in his remark.........

Unless I am mistaken his point was that it would have been more appropriate had the links been to the data on this site.

He can correct me if I'm mistaken.

Rod

dvdhawk Mon, 06/01/2015 - 12:18

Rod Gervais, post: 429487, member: 12386 wrote: I believe you missed the sarcasm in his remark.........

Unless I am mistaken his point was that it would have been more appropriate had the links been to the data on this site.

He can correct me if I'm mistaken.

Rod

It's certainly possible Rod. I could be filtering that through some comments Chris made recently about the Studio Construction and Acoustics sections of RO, in a thread that was eventually purged. I know he's been laboring through cleaning up old dead links and recently made more accommodations for uploading files here.

In any case, the fact that we can ask experts like yourself for their advice is priceless. I don't expect any of you to give away the store. It is how you and many of these experts make a living.

pcrecord Mon, 06/01/2015 - 12:59

dvdhawk, post: 429498, member: 36047 wrote: I don't expect any of you to give away the store. It is how you and many of these experts make a living.

I find that opening a door with partial informations is worst than giving no information.

As many years as I've been here, I never withhold any information that could help someone to better record or mix even if that's a part of my living. I guess participating in a forum is more than making money to me. It's supposed to be a sharing, you give I take, I give you take...

Audio acoustics is something hard to learn and I wish we could build an article or guide or anything that could make sens for EVERYone ;)

dvdhawk Mon, 06/01/2015 - 18:32

pcrecord, post: 429499, member: 46460 wrote: I find that opening a door with partial informations is worst than giving no information.

As many years as I've been here, I never withhold any information that could help someone to better record or mix even if that's a part of my living. I guess participating in a forum is more than making money to me. It's supposed to be a sharing, you give I take, I give you take...

Audio acoustics is something hard to learn and I wish we could build an article or guide or anything that could make sens for EVERYone ;)

Marco you've proven yourself to be a pillar of the community here and very generous with your time and helpful advice. I sincerely admire your efforts and commend you for that, but this 'give and take' doesn't affect your livelihood in the same way.

You have a lot of experience and knowledge to share, but you make your living recording music and providing photographic services, so a better analogy would be if we all showed up at your door expecting you to record our album for free and shoot the cover photo for free while you're at it.

I don't think anybody is withholding information, but by the same token people who have dedicated their lives to acquiring the expertise to write a book shouldn't be expected to give away the contents online anymore than you should be expected to give away the music you've created.

These fellows have been extremely generous with their time sharing their knowledge and experiences over the years, and we're lucky to have the chance to learn from people waaaaay further up the ladder than we are. To me that is what a forum like this is about, reaching back and helping someone else behind you come up a rung or two.

Audio acoustics is a very challenging subject.

I'm happy to freely share the four main things I discovered trying to learn more about acoustics via the internet, which are:
1) The web is full of self-proclaimed 'expert' acousticians, mis-guided theories, and .
2) One size does NOT fit all.
3) Beyond "get the F. Alton Everest Master Handbook of Acoustics" the 'experts' don't agree on a lot of things.
4) Lots of the 'experts' DO have product to sell, so you always have to consider the source, their professional track-record, including their biases toward their own product.

With great respect and appreciation to you and all who share their time and talents here,
Dave

I apologize to ChrisH, if we've veered off-topic.

pcrecord Mon, 06/01/2015 - 18:56

dvdhawk, post: 429508, member: 36047 wrote: So a better analogy would be if we all showed up at your door expecting you to record our album for free and shoot the cover photo for free while you're at it.

To me it's very different to explain to you how to do something and do it for you. I'm not expecting anyone to travel here and acousticly tune my room for free. But, pointing me to the right tools with explaination I can grasp is something I wish for. Thinking that acoustic know how is more important than mic placement and mixing techniques is like establishing that they are better persons because they know something or that knowledge is more important than others.

I totally respect anyone taking time to help and explain any small part of a process (in any subject). I read very helpfull acoustic posts here in the past, so I'm not condaming anybody. I agree with you [[url=http://[/URL]="http://recording.or…"]dvdhawk[/]="http://recording.or…"]dvdhawk[/], some experts gave great help and should get our gratitude. but I just wish one of them go a bit further and establish some tools with simple instructions to help at least small projects like so many of us need to start off.

Maybe all the information we need is available online and we just need a educated eye to put it together here it a well layout article ;)

audiokid Mon, 06/01/2015 - 22:05

dvdhawk, post: 429482, member: 36047 wrote: With all due respect, you've just missed them because it didn't interest you. I've seen, and read, countless resources over the years that were posted here by acousticians and builders - because it interests me very much. Thanks to Rod, Andre, Brien, Max, Glenn (Gulfo), Wes, Eric, Etc.

Acoustics (live or studio) and how this directly improved my business has always interested me. I attribute that to my long career but it still blows my mind that we have had so many threads and pro's here and not one of them is as useful as the links Kurt posted. Go figure. Or better yet, why?

I understand the links and the importance of a lot more than just gear, just not why we have never had better in 16 years online.

Glad to be of service for them though. 16 years and counting :)

Back to the OP.

kmetal Mon, 06/01/2015 - 23:23

pcrecord, post: 429510, member: 46460 wrote: To me it's very different to explain to you how to do something and do it for you. I'm not expecting anyone to travel here and acousticly tune my room for free. But, pointing me to the right tools with explaination I can grasp is something I wish for. Thinking that acoustic know how is more important than mic placement and mixing techniques is like establishing that they are better persons because they know something or that knowledge is more important than others.

I totally respect anyone taking time to help and explain any small part of a process (in any subject). I read very helpfull acoustic posts here in the past, so I'm not condaming anybody. I agree with you [[url=http://[/URL]="http://recording.or…"]dvdhawk[/]="http://recording.or…"]dvdhawk[/], some experts gave great help and should get our gratitude. but I just wish one of them go a bit further and establish some tools with simple instructions to help at least small projects like so many of us need to start off.

Maybe all the information we need is available online and we just need a educated eye to put it together here it a well layout article ;)

The best analogy I can think of, would be if we re-mixed the songs in the the mix critique section. If we took those tracks loaded them, edited them, mixed them, then said, go get them mastered and packaged. Or if Boswell did a new circuit design for tons a people in the DIY gear sector, with whatever extra they had around the house. That's the tedium of studio planning as soon as you get past basic room modes and putting absorbsion in the mirror points.

One of the experts did establish easy to use tools, that were just fine for people interested, who don't have a huge math background, but know what they need to calculate. The spreadsheet came as part of the book.

To be quite honest, most enthusiasts looking to 'tune up' a spare room need nothing more than some superchunk bass traps, and some absorbsion panels at the mirror points, and a ceiling cloud.

People looking to modify the room in a structural way, need a better understanding of acoustics, and are usually in search of 'soundproofing' which is often confused with isolation. They also need familiarality with tools, and construction terms, which are a completely different skill set than acoustics, and one doesn't necessarily come with the other.

I've barely seen any posters over the years follow the sticky, wich clearly states what info to include.

Acoustics is not a one size fits all, just like eq ing a kick isn't. There's the basics then There's specifics. The amount of generosity in these forums is amazing in all sectors.

I'm not saying we shouldn't compile a nice organized set of info, we should, but it's difficult to draw a line in the sand when your talking about something like plans for a studio build, and that's up to each person. This stuff gets into high math and science quickly, and there isn't much more that would even be useful to the common musician even if they were told. It's too much. I barely understand it, and I'm trying to.

The thing is, acoustics and acoustic construction are separate but related. designing a wall panel to resonate below 80hz, and designing the wall to it fits in someone's space starved room, in between pipes, the dog house, and some beam, are different areas of expertise, which are related. Somebody could be very knowledgeable in acoustic architecture or design, but have not know necessarily how to make a pocket cut for a roof vent, physically be able to do it well. People who know music theory, don't all know how to make a guitar or violin.

I see what your saying Marco. It seems very grey for beginners. And it is. Eventually it'll come together, but there are tons of people who just don't take the good advice, and realistically there isn't a whole lot the average musician needs to know about it.

I hope we continue to hear from the knowledge experts in this area, and they're varying opinions. One of the things I like about acoustics is it isn't an exact science, even at the highest level. So there is some room for different schools of thought, new discoveries, and creativity. I for one know I am very thankful, anytime I am able to get advice from the experts, especially in the acoustics arena, as it is the least well known area of the musical realm.

-kyle

DonnyThompson Wed, 06/03/2015 - 02:36

I've learned more here on RO about acoustics in the last year or so, than I ever did over my entire career, which spans 30+ years.

That being said, it's still not an easy subject for me to grasp... like most here, I know "basics", but there are many, many things I've yet to learn about it.

Kyle mentioned

kmetal, post: 429514, member: 37533 wrote: there are tons of people who just don't take the good advice, and realistically there isn't a whole lot the average musician needs to know about it.

And I agree with him. The vast majority of home recording hobbyists don't really know much, and a large percentage of that majority doesn't really care all that much about knowing, either.

Mostly, they are looking for quick and easy answers; and often, are expecting "miracles" from applying a half-dozen 1" auralex tiles in their bedroom, basement, attic, etc.

The better educated we become about acoustics,( or for that matter, anything audio related) the more prepared we are to tackle the problems that are presented to us, and just as importantly, it advances our understanding of knowing how to use that knowledge.

I think that perhaps the biggest problem most people have with acoustics, is the vast amount of myth that is available out there.. Myth touted as being "fact".

People who don't know, and who are looking for those "quick and easy" fixes I've mentioned above, aren't basing their problem-solving on fact. There's so much misinformation about it, and because so many people would rather take the easy road, they end up spending money on treatment devices that are not only cheaply made, but in many cases, aren't even the correct type of treatment for their room's issues. The number of home studio's that I've been to as a consultant, that had wall to wall and floor to ceiling 1" auralex foam, is much, much higher than those that have installed correct forms of treatment, and having based it on acoustic facts instead of propagated internet myth ... or word of mouth from a "friend", who is usually a neighbor that set up his cousin's home theater system. :rolleyes:

And - when asked why they have done this type of treatment to their rooms, one of the most common replies I receive is "I wanted to absorb the high frequency "ringing" and the "whoompy sounding" bass frequencies..."
The second most popular response is "I'm trying to sound proof my room so no one calls the cops when I do drum tracks at midnight..."

When further queried as to what made them think that this particular type of treatment was the correct treatment for those issues, it's always "I read an article/blog/forum post about it on the internet and this is what it said I should do."

The education, truth, and the facts are out there, fellas. All you have to do is read the respected works from guys like Alton Everest - who took the time to write a book about it, which is still used by professionals and respected to this day as a standard in the field - or, any of the other respected works written by people who know what they are talking about. Rod's book, an excellent piece of work, simplified it just about as much as anyone ever could. But.. that requires time, and study; which are both things that very few care to do in this day and age of "I want it easy, I want it automatic, and I want it now..."

The " fix-it-by-myth" method requires far less time, is easier to grasp, and easier to apply. It's all wrong, of course, but hey, at least you can get it without straining your brain, and, you don't need to wait or be bogged down with something bothersome like the facts... so while you'll get it all wrong, at least you can get it "now". ;)

kmetal Wed, 06/03/2015 - 13:59

The absolute bottom line to all of this from my humble experience is this- People don't want to hear or accept that they can't afford what they want or need. next step is them not accepting the limiting factors that exist, leading to endless tweaking and pondering. Nobody honestly wants to say, yeah my spare room studio kinda sucks, and I know I'll never put out mor than decent prosumer music.

Instead, the boards are full of often ignorant, blind enthusiasm, and the people continually trying to fit the proverbial square peg into the round hole.

That's why I say it'd be great if there were some references as to what kind of response you could expect from average rooms. Kind of a +/-3 type 'standard' but for average rooms with basic treatment.