Member for

21 years
I would like to make my own cables. What recommendations do you have for quality cable and connectors. I need to make balanced 1/4 to 1/4 and XLR, as well as instrument cables. I want quality but have a limited budget.
Thanks for your help.


Searching for info on soldering, found this post.
Also found an epic thread about some fellow mutilating a nice old mic w/ bad soldering techniques.

So I ask you Cucco (or anyone, for that matter), what are your recommendations on information?
I have some very basic soldering skills and a cheap kit (brief stint @ ITTs Electrical Engineering program), but have realized that while what I have may be sufficient for practice, I'm gonna need some instruction and eventually a better setup.

Since I've decided to do this job in one form another, I've decided to acquire the necessary skills. Like making my own cables and fixing bad connections.
Besides, I just got a cheap old BlueTube on eBay that came in a rackmount (no top piece) with a BlueMax - and it's got a lot of noise (AC & RFI). One channel does better than the other.
I've decided to make it work properly, starting w/ grounding/iso, and then further if necessary.
I only mention the BT b/c it made me realize I really need to be able to tinker w/ things better - rather than have the local guy charge me more than the cost of the item to fix it. We do call ourselves engineers?

Member for

17 years 6 months

Hey jonmmartin -

Welcome to DIY cables! It's fun and addicting. Here are a few tips -

1 - Get a good soldering iron (if you don't already have one of course...) A good Weller soldering station with variable output is a great solution.

2 - Get good solder. At a minimum, get Kester silver-bearing solder. WBT is good as well, but a bit more expensive. DO NOT use plumbing solder or pretty much any other kind of solder that you can buy from Lowes or Home Depot.

3 - Make sure you make good connections - never a cold joint. (If you're not familiar with soldering techniques, read up a lot and practice on stuff you don't care about.)

Good cable brands include:
Canare (my favorite for most applications)
West Penn (inexpensive and quite nice especially given its price)

Then you have to decide whether you want quad, non-quad (4 leads, 2 leads respectively) braided shield, non-braided shield, etc. Mogami uses a non-braided, twisted shield which is easy to work with but I find is less effective. Canare uses primarily a braided shield which is a pain in the ass to work with be incredibly effective. Belden goes either way depending upon the cable.

The reason Canare is my favorite out of the brands listed is because of quality and because the jacket is smooth and coils easily. I can't say the same for all others. last tip. Have good ventilation. Solder is nasty stuff - the fumes will kill you (literally) if you're not careful.


Member for

17 years 6 months

Connectors are roughly $2-$3 per piece (Neutrik XLR and TRS).

Cable itself can run you anywhere between around $.20 per foot up to $2 per foot (for single cable) and $1 per foot up to $25 per foot for snake cables.

Solder should set you back about $30-$50 per roll but will last a bit.

You'll likely need some shrink tubing as well (which is inexpensive). A hot hair dryer can shrink it, but a cheap heat gun works best (Lowes - $39 in the paint aisle.)

Member for

19 years 10 months

did someone say ... DIY !!

be a little careful when using Heat Guns as they do have enough grunt to melt cable outers
and some connector parts
and damage the heatshrink tubing itself

Soldering is much easier with a real solder station and a selection of iron tips
I use a Webber but many use the Hakko

it may suprise people to learn that I use the simple plastic (Cliff) 6.5mm TRS connectors
this is for inside racks where repeated use is not an issue

cheap with a good chromed outer
accepts solder well
does tarnish like others do

yes the Neutrik and Alcate (Canon)l XLR and TRS connectors are what I use in the ... open ... so to speak