USB, AES/EBU,HDMI together?
Forums
I need to run at least 2 boosted USB, 2- 8Channel AES and a DVI-D (or possibly an HDMI instead) cables together in about 30-35' of PVC.
Will this create issues like crosstalk, inductance, speed reduction, clicks, clocking issues, bandwidth reduction, RF and other things I may not be aware of?
USB: 1. Houston Controller to/fro MAC
2. Pure 2 ADDA to/fro PC
- Read more about USB, AES/EBU,HDMI together?
- 21 comments
- Log in or register to post comments
- 36 views
impedance question
Forums
Hi Dave... I have a question about the ADK AP Preamp... I know you have one, so I thought I might pick your brain about on thing in particular...
- Read more about impedance question
- 4 comments
- Log in or register to post comments
Impedance question with mic preamps.
Forums
I am mildly versed in electronics. I understand that when you plug a mic into a mic preamp the mic expects to "see" or "react" to a specified impedance. I think that you want the mic preamp circuit to be x amount higher impedence then the mic (maybe I have that backwards).
- Read more about Impedance question with mic preamps.
- 6 comments
- Log in or register to post comments
- 61 views
Impedance Matching
Forums
I just acquired the PreSonus Eureka Channel Strip. It has a pre-amp, compressor, and eq for one channel. One of the knobs is the Impedance. From reading the manual, it says to adjust the knob to the impedance for whatever microphone I am using. It also says to try different combos to experiment, but that is all it says.
- Read more about Impedance Matching
- 2 comments
- Log in or register to post comments
- 3 views
30/50 ohm mics, how to match to medium impedance
Forums
Hi,
- Read more about 30/50 ohm mics, how to match to medium impedance
- 2 comments
- Log in or register to post comments
- 256 views
Old Shure Unidyne Impedance Question
Forums
Trying to figure out of I can use this thing with a preamp. I'm not too up on all this impedance stuff - you probably noticed. :tongue:
- Read more about Old Shure Unidyne Impedance Question
- 7 comments
- Log in or register to post comments
- 303 views
High vs Low Impedance, and why I think the general terminology is wrong
Forums
I am sure that as engineers we are all familiar with the terms high impedance, and low impedance. These words are usually used to describe a signal, and the load level that is needed by the signal.
- Read more about High vs Low Impedance, and why I think the general terminology is wrong
- 7 comments
- Log in or register to post comments
- 9 views
trying to understand "impedance" and "line level"
Forums
I'm trying to understand inputs. I have an electric bass guitar that I'm running into a UCA202. The bass is passive and I don't have a pre-amp. Going from the UCA202 to my DAW (Logic Pro), the bass sounds okay.
- Read more about trying to understand "impedance" and "line level"
- 3 comments
- Log in or register to post comments
- 19 views
Determine the cut off frequency of any filter formed from output impedance and input impedance
Say you have a piece of electronic equipment which has an input impedance of 1Megohms, and an input capacitance of 10 picofarads as determined by a ceramic capacitor across the input resistor. This obviously creates an RC impedance filter which will act on any AC entering the device.
Calculating and Metering Total Impedance (Guitar related)
Forums
I am trying to calculate/meter the total load I am showing the pickups, but I'm a bit confused. I have a few mods in there to alter the sound of the pickup. The pot is 500k and wired with hot lead to lug 1, lug 2 is output and lug 3 is bent back and soldered to the base. I have 333k resistor and 1000pF cap between lug 1 and lug 2. I also have a 1M resistor between lug 1 and lug 3.
- Read more about Calculating and Metering Total Impedance (Guitar related)
- 26 comments
- Log in or register to post comments
- 46 views