Skip to main content

I'm using an AT-2020 mic for vocals, and a Behringer AUTOCOM PRO MDX 1400, should i be using the Behringer or is there somthin else i can use to get the vocals clear and remove the hissing sounds from the microphone. someone recommended the ART tube preamp, but i dont want to buy the wrong piece. .

Tags

Comments

jonyoung Fri, 04/11/2008 - 14:31

The hissing sound is most likely from the Behringer. Self noise from mics is generally pretty low, 20dB SPL in the 2020's case.....not world class, but very decent. I own a pair of them, run them through an ART Pro MPA when doing vocals or acoustic instruments, hissing is never an issue. Hope this helps.

Davedog Mon, 04/14/2008 - 12:14

The hissing you hear is the reaction of the entire recording community finding out you use B**&^%$#GER stuff.

I had an Autocom that did the same thing. I was lucky to get the $50 I sold it for.

The ART MPA is a very good unit that you'll likely keep even after you 'graduate' to much higher end pieces should you continue the process of becoming a recordist.

Do NOT confuse this with any of the 'lower end' ART pieces. It is NOT the same animal.

Link555 Wed, 04/16/2008 - 07:11

just to restate Davedog opinion, avoid the lower lines of ART, like the tubepac. I have never seen such a terrible tube design as the the tubpac. No thought went into the heat issues in this design. Infact it tooks 4 month of concentrated tweaking to make work and sound decent.

You might also want to look at other pre-amps like Aphex,Grace, FMR...

anonymous Thu, 05/01/2008 - 19:27

Davedog wrote: The hissing you hear is the reaction of the entire recording community finding out you use B**&^%$#GER stuff.

I had an Autocom that did the same thing. I was lucky to get the $50 I sold it for.

The ART MPA is a very good unit that you'll likely keep even after you 'graduate' to much higher end pieces should you continue the process of becoming a recordist.

Do NOT confuse this with any of the 'lower end' ART pieces. It is NOT the same animal.

I've been looking at picking up an ART MPA recently, hoping to get it on Saturday. Is there a large difference in sound/quality between the $300 MPA Gold and the $400 Digital MPA? If not, I really want to spend the least amount of money possible, since I can barely BARELY justify the $300 in the first place. Also, will the MPA Gold cooperate with my M-Audio Firewire Interface? (I'm running into protools).

bent Thu, 05/01/2008 - 20:06

Well, I know Protools can do it.
No problem there.

As far as wiring - Which M-Audio box are we talking about?
The Solo has separate line inputs, as does the FW410...

Connect a female XLR cable to the output of the MPA.
Connect a female XLR to male TRS turnaround to the other (male) end of the cable and plug it into the M-Audio box, hit the mic/line switch to line if applicable..

If the input is 1/8" stereo (I have no idea which M-Audio product that would be), then you'll need a dual (stereo) female XLR to male (stereo) 1/8" plug.

anonymous Thu, 05/01/2008 - 20:15

bent wrote: Well, I know Protools can do it.
No problem there.

As far as wiring - Which M-Audio box are we talking about?
The Solo has separate line inputs, as does the FW410...

Connect a female XLR cable to the output of the MPA.
Connect a female XLR to male TRS turnaround to the other (male) end of the cable and plug it into the M-Audio box, hit the mic/line switch to line if applicable..

If the input is 1/8" stereo (I have no idea which M-Audio product that would be), then you'll need a dual (stereo) female XLR to male (stereo) 1/8" plug.

It's the firewire solo, yeah. I don't think I'll be able to do it with XLR cables, but I can't remember exactly. Either way, I think I'll be able to pull it off. Thanks a lot for the help!