i run my snake into a Mackie 24/4 vlz pro mixer and use the insert TRS to send out into my preamp and then to compressor and then out to my multitrack interface (MOTU 24i). on the first two channels i run board/preamp/compressor. on the others i run board/compressors with no external pre. am i running everything in the correct order? i dont feel like i am able to push my preamp very hard and I'm not exactly sure why. i assumed that in order to control the input into my compressors or pre's i would use the insert out of my board and use the trim knobs to control how much of a signal to send out to my compressors. i would like to hear from the board the sound i get post pre's and compressors, i just dont wanna go snake straight into my pre and have it clip and not be able to turn it down. any help? sorry if i am not making much sense here...I'm at work and ive been going since 630 this morning. thanks for any help.
Comments
Your signal chain should be: Microphone into snake input. Snake
Your signal chain should be:
Microphone into snake input.
Snake output into boutique microphone preamp.
Boutique microphone preamp output directly into 24i input channel of choice. NOT into the Mackie at all.
For the other microphones. Into snake input.
Snake output into Mackie microphone preamp input.
Inserts output into 24i input channels of choice.
Adjust microphone preamps gain trim for proper recording level through the 24i. Your boutique preamp and the Mackie should have ample output to properly drive the inputs of the 24i. If you're getting distortion on your tracks, trim the gain down. Average recording levels should be between -18 to -6 as indicated by your software's meters.
You're almost there!
Ms. Remy Ann David
thanks for the help remy, that was exactly what i needed. i had
thanks for the help remy, that was exactly what i needed. i had a feeling that was what i was supposed to do considering having a signal path basically running through 2 preamps.
one more question for you ms. remy if you dont mind...
the only reason i run anything through the board in the first place was to be able to send headphone mixes out of one of the aux sends. i have problems running headphones mixes out of my daw (cubase sx3) because there seems to be a tiny bit of lag. while tracking into cubase i use the monitor on each channel and that sends back out to the headphone output of my motu and there is that lag so i just send the mixes to the headphones out of the board. i know that i am doing this so terribly wrong but i cant figure out a way to get better headphones mixes. i want to have the headphones mixes with good eq, maybe some compression or even reverb for vocalists and i know i have to do this within cubase but the lag stops me from that. if you read all of this and understand you truly are my hero.
p.s. one day i will meet you and shake your hand for teaching me so much from these forums. i search out your posts to try to find answers and sure enough, you always have the right one.
That lag you are hearing is from the inherent latency of whateve
That lag you are hearing is from the inherent latency of whatever soundcard device you are using. This differs with each manufacturer. Sometimes, there are settings recommended by the manufacturer of the audio interface device that will allow for lower latency. But because everything is digital and must be processed from input to output, there will always be a tiny minute amount of delay that most everybody has to deal with. If you can get the latency down to less than 15 ms, you should be able to work with that? But I have seen/heard the latency grow to over one second when combining audio with video and monitoring output.
Some software bundles that come with certain sound cards offer a straight through input to output monitor feature that virtually eliminates latency during tracking and monitoring. Not everybody has those sound cards and so latency with those may be more of a factor.
So I might have to recommend that you contact the manufacturer of your sound card and discuss the latency issue with them and any improvements they can offer you?
Thanks for your lovely comments
Ms. Remy Ann David
dennisisme wrote: i run my snake into a mackie 24/4 vlz pro mixe
what :shock:
no
The mic input of the Mackie IS the pre-amp
fine the insert is at line level and so the comp
and then comp to the the multi-track sould be fine
no
first two channels
Pre-amp ... line level
compressor
then to the Multi-track
OR
line level input of the Mackie so you could use the EQ if you wanted to
what ?
which pre-amp (brand and model) are you talking about ?