Skip to main content

I just wonder which mics are good for guitar recording. So, which mic would be the best for a tight, distorted guitar?

I helped some friends recording a demo/CD and we couldn't get a good sound. Right now I can't remember which mics we used, but we want to go over it again.

We are using a Carvin Legacy with matching 4x12" cab and a Tube Works 1x12", 100W combo with a 1x12" extension cab. Very different sounds and they're a pain to match.

Suggestions? Thanx in advance.

Comments

nrgmusic Sun, 08/26/2001 - 10:37

Originally posted by Guitarwiz:
I just wonder which mics are good for guitar recording. So, which mic would be the best for a tight, distorted guitar?

I helped some friends recording a demo/CD and we couldn't get a good sound. Right now I can't remember which mics we used, but we want to go over it again.

We are using a Carvin Legacy with matching 4x12" cab and a Tube Works 1x12", 100W combo with a 1x12" extension cab. Very different sounds and they're a pain to match.

Suggestions? Thanx in advance.

Guitarwiz
here are the mics I tend to head for first of course ymmv but they seem to work for me and not necessarily in order:

md 421
sm57
sm58
e609
u87ai
c414
u47 fet
royer r121/sf12

plus of course a bunch of different mic pres...

hope this helps and of course it depends on the type of music.

Simon :)

Aaron-Carey Sun, 08/26/2001 - 18:19

here is a screen cap from IRC while I was explaining how I used a trick from my favorite engineer in the world:

"
ok not like its big head or anything, just how I do it
first you need at least two mics
and hopefully a console, at least some sort of summing system, and mic pre's with a phase reverse, or if you use extreme ghetto technology, a out of phase cable and an in phase cable
lets just say that you are doing heavy barfing death palm muting stuff for this
so you dont want much room sound, just big chunk, so when you stop playing it stops....this will work for a bigger with room sound too, but this is for example
I say that stuff so I can say for this example, just two mics, on a 4x12 one mic on axis right into the center of the cone, one mic on a different speaker, off axis sorta, pointed at almost the surround, but still inside the speaker
ok now, make some sort of steady noise, hum ( easy if you have a fender strat) or maybe put your guitar near a VGA monitor, or even just plug a tone generator into the amp
now bring up the first mic ( i am assuming a console for this, tailor to youer needs as necessary)
turn it and the gain till you got zero of some sort on your meter, just from the noise
now leave the first mic fader where its atr, but hit the mute for that channel
now bring up the other mic on fader # 2 till it is at zero
now turn on fader one( unmute) see if the levels drop as if they are out of phase, if not hit the phase switch till it looks out of phase so the level drops
set it so that the faders are out of phase for sure, and make sure they are at the same level
now, cancel your health insurance, tell everyone around DO NOT TOUCH the guitar or tone generator or whatever...
put some headphones on that hear the two faders ( like control room mix to your headphones)
go out in the room with the amp make sure the headphones are so loud you dont hear the amp direct, only the mic'ed signal
now you should hear a hum or tone or whatever noise you are sending in your ears in your headphones
now move the mics back and forth relative to each other, and you will hear phasey, flangey whooshing noises
at some point, they will be SO out of phase that you will not hear JACK in your headphones...stop right there and rejoice
now go back out to the console and flip the phase switch to opposite what it was
you now have a " theoretically " in phase guitar mic setup
it will be fat ass and shit, you can push the faders back and forth nowe that you know theyre in phase and all
use the faders as your primary eq, the two mic piositions will be different enough that you will get a wide range of sounds just by pushing them
also as a variation on this, the phasing trick works best at the frequency of the tone you sent it...it is most accurate at that frequency, thuis if you are most worried about a certain part of the tone, you can use a tone generator to send that frequency, and phase using that...

You can make for a bigger, more room, sound and still be in phase-ish as you are phasing the mics, just keep moving back away from the cab, you will hear it get louder and softer, in cycles. After 1 or two cycles, you will probably have to turn up the mic preamp gain at the console, as the mic being further away will bring it to less than zero.

you can use more mics, different mics, whatever, just be aware that phasing will be a little less between unmatched or more mics...but youll figure it out

Also once you are done, you can stick the tracks in a PC editor multitrack app and line the phase up even more! You may think to just throw two mics up and phase them in your app later, BUT it is EASILY possible to have two mics in phase, but have them in places that DONT sound good. Better to have a good idea first of how it will sound!

feel free to e-mail me at
pipelineaudio@angelfire.com
looking for coders to help me make my own app and some sorely needed fx"

Hope that helps

Guest Sat, 09/01/2001 - 12:14

Originally posted by Guitarwiz:
I helped some friends recording a demo/CD and we couldn't get a good sound. Right now I can't remember which mics we used, but we want to go over it again.

We are using a Carvin Legacy with matching 4x12" cab and a Tube Works 1x12", 100W combo with a 1x12" extension cab. Very different sounds and they're a pain to match.

They're a "pain to match" to each other, or a "pain to match" to the original track you don't like?

May I suggest that you get a sound from either [or both] that sounds excellent in the room, and then worry about capturing the sound.

Too many people seem to feel that shit like microphones and preamps can make up for a deficiency with the 'tone and touch' aspects of playing an instrument. I'll give you a hint, recording engineers don't do 'alchemy', they take waveforms out of the air, and store them. Period. If the sound isn't there to begin with, there is no way in hell you can capture it.

If the sound is there, then fuck with microphone selection and placement until it fits with the rest of the tracks that comprise the song.

One thing I've found to be most helpful...get the cabinet at least 3' off the ground. Probably because I'm old and don't like to bend over to listen to a guitar amp...but frankly, the guitar's I've captured over the last few years that were at least 3' off the ground seem to have come out the best.

As always, YMMV.

anonymous Sat, 09/08/2001 - 09:47

I have very good results with Beyer M69 or M88.
The 88 has more low end than the 69. The Beyer M201 is also very good.

In case you record the whole band in the same room I guess they're the best you can have.

I did lots of (metal) bands and used Sennh. 421/441, AKG C1000/3000, and many other mics on dist. guitar, but I mostly use the Beyers now, they're great :)

x

User login