x
Description

Phantom power, in the context of professional audio equipment, is DC electric power transmitted through microphone cables to operate microphones that contain active electronic circuitry. It is best known as a convenient power source for condenser microphones, though many active direct boxes also use it.

FAQ

Can voltage fluctuations in the phantom power (PP) cause microphone hiss?

It's very unlikely that voltage fluctuations in the phantom power (PP) could cause hiss.

What are the 3 pins for phantom power?

There are three pins. Phantom power is connected to both pin 2 and pin 3 (but as long as your cable is not broken, simply use it).

X stands for ground (it is connected to the cable shield).

Pin 1 (X) = ground
Pin 2 (L) = + most commonly, or Left
Pin 3 (R) = - most commonly, or Right

Will phantom power damage dynamic microphones?

The risk is higher if it is an unbalanced connection. The Sound Reinforcement Handbook by Yamaha says something like this:

"In a phantom power system, the polarizing supply voltage is placed on both of the signal lines in a balanced connection, with the same polarity on each line. Dynamic microphones connected in a balanced system with a phantom power input are then protected from damage, theoretically, since the system results in a net zero DC potential across the coil. However, a dynamic mic connected unbalanced to a phantom power input may be destroyed."

In other words if you take a sm57 and plug it into a phantom powered mic pre using a normal balanced mic cable then you should be safe.

If you take an unbalanced mic and wire it with a xlr plug so you can connect it to that same input then you could fry the mic. In a balanced connection the 48 volts is running parallel down the 2 signal wires. With an unbalanced connection (2 conductors) you have 1 signal wire and ground and doing this is basically completing a circuit that sends 48volts directly to the mics voice coil.

What are the correct steps connecting a mic to phantom power

So the steps when connecting are:

1. Turn down those master faders.
2. Plug in mic.
3. Turn Phantom Power on.

and when disconnecting:

1. Turn down those master faders.
2. Turn Phantom Power off.
3. Unplug mic.

Joemeek VC3, hum and hiss whenever I turn on the phantom

anonymous 3 September 2004

Forums

I JUST GOT A JOE MEEK VC3, AND WHENEVER I TURN ON THE PHANTOM POWER, I GET A LOT OF HUM AND HISS. IS THIS DUE TO THE CRAPPY WAL-WART POWER SUPPLY THAT CAME WITH IT? I HEARD THAT SOMEONE WAS EXPERIENCING THE SAME CONFLICT AND THEY PURCHASED A ROLLS PS-12 POWER SUPPLY AND IT MADE THE SIGNAL MORE QUIETER. PLEASE HELP, THANKS.

Rack Mount Phantom Power + Phase Reverse

anonymous 17 December 2003

Forums

Does anybody know about a rack mountable unit that will provide phantom power AND phase reverse switching functions? My Aardvark Q10 does not have phase reverse capability.

I looked at the Little Labs device, but it is not what I'm searching for, plus the price is too high. I need a rope and tire solution, not a gilded lilly.

Use mic's own phantom power or pre's?

Barkingdogstudios 8 December 2003

Forums

I'm using an AKG Solidtube microphone which comes with it's own phantom power supply.

My pre also has phantom power available which I can turn on or off. Should I continue to use the AKG's own supply unit (figuring that it's likely better calibrated to the mic) or am I just introducing another layer of unecessary hardware into the chain?

Can phantom power destroy inputs?

anonymous 16 November 2003

Forums

Have a problem on my Tascam US 224 where I suddenly lost all input signal on my XLR and line inputs.

This hapened right after I connected my RODE NT1 to the unit, via an external phantom power supply that was already switched on.
The volume ouput on the soundcard was set at zero, but one trim pot was set at maximum.

x

User login