428 TO RNC distorting again!
Well just to let everyone know, last night again when connecting the 428 to rnc through inserts, it distorted again on vocals when I sang loud. I give up. I am using the analog compressor in the Korg 32xd now and that works just fine. BLAHHHHHHH! :evil:
justin
- Read more about 428 TO RNC distorting again!
- 2 comments
- Log in or register to post comments
So how abou that RNC (the compressor)
I think its one hell of a compressor, and its cheap as hell.
- Read more about So how abou that RNC (the compressor)
- 5 comments
- Log in or register to post comments
RNC across the mix bus.
Hey guys.I have the much hyped (for good reasons) RNC in my rack.So I strapped it across my main mix inserts to get more juice off the mixes. I am in super nice mode to get that triple compression thing. Is it me or there is no way to get usable boost off this box for my mixes, without hearing it pump.I tried every configuration I can think of.
- Read more about RNC across the mix bus.
- 14 comments
- Log in or register to post comments
Aardvark Q10 + Meek MQ3 + FMR RNC
In about a week and a half I will be hooking up my MQ3 Pre and my FMR Really Nice Compressor to my Aardvark Q10.
I am looking for any advise, guidance, auggestions, experiences from users who have used either the meek or the rnc with a Q10.
Here is my quick plan.
- Read more about Aardvark Q10 + Meek MQ3 + FMR RNC
- Log in or register to post comments
Avalon 737 vs. . Speck/Speck/RNC
I just picked up a used VT-737sp (for a song).
I have been testing it for only two days, but honestly, I am having a hard time seeing a marked increase in quality over my usual "channel strip" of the Speck MicPre 5.0>Speck ASC EQ>RNC.
- Read more about Avalon 737 vs. . Speck/Speck/RNC
- 11 comments
- Log in or register to post comments
How to setup RNC in a balanced signal path?
I just got an RNC, and I'm not sure how to set it up. The manual explicitly says you can't use it in a balanced signal path with TRS connectors. You must "unbalance" the signal first.
My plan was to use it in the balanced insert loop on my PreSonus MP20 pre. The outs (balanced) of the MP20 then go into the inserts on my mixer in order to bypass the mixer's pres.
- Read more about How to setup RNC in a balanced signal path?
- 3 comments
- Log in or register to post comments
anybody use FMR stuff (really nice compressor/pre)
I'm thinking of getting the really nice compressor and then the pre-amp because they are affordable. I just wanted to know if anybody had anything to say about them.
Thanks, Beau
RNC meets Joemeek
Hi all--
First post, so hello.
I just got rid of my dbx 286A which got replaced by a used Joemeek VC1Qcs and a new RNC. I wanted more control over the compression for guitars, and vocal tracking.
- Read more about RNC meets Joemeek
- 4 comments
- Log in or register to post comments
RNC Compressor
I know that the RNC compressor from FMC has a huge (almost) cult following, and is considered "the steal" of the industry.
- Read more about RNC Compressor
- 3 comments
- Log in or register to post comments
question about using an RNC with a Studio Projects VTB-1
I just bought a Really Nice Compressor. I want to use it with my Studio Projects VTB-1 mic preamp.
The RNC instructions say:
Hooking up the RNC to balanced lines with TRS 1/4" plugs will not work! If the equipment you are connecting the RNC to is balanced, you must first unbalance it and only connect into the RNC with TR 1/4" plugs.