RME Multiface or M-Audio1010 ?
Forums
I'm gonna have to choose one, please help me. Which one has better D/A conversion ?
I'm mostly interested in the sound quality between the two. thank-you in advance
- Read more about RME Multiface or M-Audio1010 ?
- 2 comments
- Log in or register to post comments
memory allocation/deleting unused regions
Forums
Hello folks...first post on this forum.
- Read more about memory allocation/deleting unused regions
- 5 comments
- Log in or register to post comments
Impending market chaos?
Forums
So, tomorrow, or soon thereafter, Digi is announcing new generation TDM hardware and the new input unit for LE. How ready are they and the third party developers for the paradigm shift? Sounds like there's going to be a 96 kHz gml/oxford eq plug (likely the compressor too?), but are the other plugins going to be up to speed? Is there a need to update the Pro Control, or should it do fine?
- Read more about Impending market chaos?
- 19 comments
- Log in or register to post comments
dual processor motherboard
Forums
there seems to be a lot of mention of dual processor systems in various forums here.
consequently there is a lot of referral to MSI's dual athlon board, but it seems like not many are aware of the others.
ASUS just recently announced their athlon dual processor solution, the A7M266-D (AMD760 MPX chipset)
- Read more about dual processor motherboard
- 11 comments
- Log in or register to post comments
Recordings with Neve Sound?
Forums
Hi. Can anyone recommend a specific recording with extensive use of Neve preamps, both vocal and for tracking instruments? A recent recording with a clone would be fine. I have seen the mantra repeated here numerous times and would like to hear for myself. I am a hobbyist getting serious about my tone.
- Read more about Recordings with Neve Sound?
- 13 comments
- Log in or register to post comments
Anyone else think ADATs sound better than Pro Tools?
Forums
I did a three piece band on ADATs, thru a Tascam board. Made a ruff mix of one of the songs on the Tascam. Then, digitally transferred the ADATs into Pro Tools LE, set to the same sampling rate and bit depth. Tried a ruff mix internally in Pro Tools, and the ruff I did off the ADATs thru the Tascam desk squashes the Pro Tools mix like a grape!
To verb or not to Verb
Forums
I've noticed trends in the amount of reverb used on lead vox. With more modern recordings leading to more of a dry sound, but I'm sure there is still a little bit being used. Are there any hard and fast rules? should the reverb be stereo or mono?
- Read more about To verb or not to Verb
- 2 comments
- Log in or register to post comments
Iwill XP333 ver. C ?
Forums
Has anyone used this Motherboard for digital audio recording? Is it easy to setup? How is the performace as a DAW? I am using a Delta 66 with Sonar. I was planning to configure the board with AMD XP1600 and 512 pc2100.
- Read more about Iwill XP333 ver. C ?
- 2 comments
- Log in or register to post comments
newbie question
Forums
i was wondering if anyone can point me in the right direction.
i'm planning on doing some software synthesis along with effects and sampling. so far i've found that Cubase will be my mixing console.
i'm looking for good quality synthesis, i've found: crusher-x live (a granuler effects program) very cool
maybe some native instruments programs
- Read more about newbie question
- 5 comments
- Log in or register to post comments
Reference Monitor Placement
Forums
I am setting up my new Hafler TRM 8s and I ran into a dilemma. I purchased some Omnistudio mounts for bottom mounting and attached the mounts to the wall. How high can I place these monitors? Can I put them above my head and then tilt them down and still get the same imaging as setting them flat? Any problems with sound this close to the wall (6-12")?
- Read more about Reference Monitor Placement
- 1 comment
- Log in or register to post comments